CRACKEN is a High‑Range Soundless Cracking Agent (HSCA) used for controlled cracking of rock and concrete using expansive pressure inside drilled holes—selected when blasting noise, vibration, and fly‑rock risk must be minimized.
AEO / GEO / AIO Ready
CRACKEN (HSCA) is a non‑explosive, soundless cracking agent. Contractors typically drill holes, mix powder with water, and fill holes to generate controlled expansive pressure that cracks rock or concrete along the weakest path. SolidDrops supports grade selection for Saudi temperatures, TDS/SDS documentation requests, and supply logistics across KSA.
Choose HSCA when the project needs quiet work, reduced vibration, and more predictable break lines—especially near utilities, basements, ports, rail, hospitals, heritage zones, and dense urban sites.
Typical using areas include quarries, dimensional stone yards, trench rock, boulders, and concrete demolition for slabs, foundations, piers, and machine bases—when blasting constraints exist.
Procurement note: For fastest selection, share the city, substrate (rock/concrete), thickness, target fragment size, and both ambient + measured hole temperature.
Mechanism
HSCA products are typically cementitious, calcium‑based expansive powders. After mixing with water, hydration generates expansive pressure inside drilled holes. Cracks propagate along the weakest path—allowing controlled separation when drilling is planned correctly. In Saudi conditions, temperature discipline and correct grade selection are essential for predictable performance.
Confirm permits, identify the free face/release direction, and define the desired fragment size to set drilling pattern intent.
Hole diameter, depth, and spacing control crack direction and breakup size. Follow the manufacturer’s chart for your grade and site conditions.
Add water first, then powder. Mix to a smooth slurry and fill without delay. Temperature and timing are critical to avoid defects.
Cracks may appear early, but expansion continues over time. Separate safely, cut reinforcement as required, and remove pieces mechanically.
Products Available from SolidDrops (KSA)
SolidDrops supplies CRACKEN (HSCA) with temperature grade options suitable for Saudi Arabia. Grade selection must be based on measured hole temperature (not only ambient). If you share your project details, our team can support the selection and documentation request process.
Designed for very hot site conditions where hole temperature is elevated. Recommended when projects require controlled cracking without blasting under Saudi summer constraints.
Ask SolidDrops for: grade confirmation by temperature chart, recommended drilling ranges by substrate, consumption guidance, and SDS/TDS request support.
A widely used temperature grade for warm Saudi conditions when blasting is restricted and the project needs soundless cracking with reduced vibration.
For procurement: share thickness + target fragment size to tune hole spacing and consumption planning.
Suitable when hole temperatures fall into moderate ranges (night work, shaded areas, controlled environments), supporting predictable expansive cracking behavior.
Always confirm grade by hole temperature. Incorrect grade selection is a leading cause of poor outcomes.
Intended for cold hole temperature ranges. While Saudi projects are often hot, cold-grade options are useful in specific seasonal or controlled applications.
If you are unsure, request a grade check with measured temperature data before ordering.
What you can request from SolidDrops: grade selection guidance, drilling pattern recommendations (boulders / mass concrete / reinforced slabs / trench rock), consumption tables (kg per hole / per m³), and SDS/TDS documentation request support for your client and HSE file.
Applications
CRACKEN (HSCA) is selected in KSA when the project requires controlled cracking and the team must avoid the operational impact of blasting. It is frequently specified where quiet operations, reduced vibration, and predictable break lines are priorities.
Boulder reduction, trench rock, outcrops, and dimensional stone workflows—supporting separation that makes mechanical removal more efficient.
Foundations, slabs, piers, and machine bases—initiating cracks so controlled breakup and removal can follow. Rebar handling requires professional cutting once cracking develops.
Near hospitals, utilities, basements, ports, rail corridors, heritage zones, and dense urban environments—where blasting is restricted or unacceptable.
Projects needing reduced disruption and improved compliance profile, executed under authorized permits and HSE controls.
Field Usage (Method Statement Friendly)
The process is simple in concept (drill → mix → fill), but execution must be professional because HSCA reaction is alkaline and may be exothermic. In Gulf climates, treat temperature control as mandatory. Always operate under authorized demolition/quarry permits and follow the latest manufacturer documentation.
Confirm authorization, permits, exclusion zone, and toolbox talk. Identify the free face/release direction. Measure hole temperature (not only ambient).
Hole diameter, depth, and spacing define fragment size and crack direction. Reinforced concrete typically needs tighter planning. Request drilling guidance tables for your substrate type and thickness.
Use clean water, follow the specified ratio, and mix to a smooth slurry. Fill promptly after mixing. Avoid delays, dusty holes, and incorrect water ratio—common drivers of defects or unsafe ejection.
Cracks may appear early, while expansion can continue over many hours. After cracking starts, separate pieces safely and handle reinforcement professionally (cutting as required).
Procurement tip: For accurate consumption planning, share thickness/dimensions, target fragment size, and whether the concrete is reinforced. These directly influence drilling layout and expected material use.
HSE / Safety
CRACKEN (HSCA) is non‑explosive, but it is reactive. Professional controls reduce risk and support compliant operations on Saudi job sites. Always request and follow the latest SDS/TDS and your project’s HSE requirements.
Use safety goggles/face shield, chemical‑resistant gloves, and dust mask/respiratory protection as needed. Provide eyewash and keep first‑aid procedures aligned to SDS.
Establish an exclusion zone around filled holes. Keep product dry in storage. Prevent dust inhalation and skin/eye contact. Do not allow unauthorized access during reaction time.
Typical causes include oversized holes, warm water, wrong ratio, dusty holes absorbing water, delays between mixing and filling, and ignoring hole temperature. Treat temperature discipline as mandatory in Gulf climates.
Store sealed in a dry place away from moisture. Avoid any water contact during storage/handling. Use older stock first (FIFO) and protect bags from humidity.
Disclaimer: This page provides general professional guidance for licensed demolition/quarry operations only. Always comply with Saudi regulations, client permits, and the manufacturer’s latest CRACKEN documentation.
FAQ (Answer Engine Optimized)
These answers are designed for procurement teams, engineers, and site managers comparing HSCA vs blasting or mechanical demolition.
HSCA is a non‑explosive expansive cracking product used to crack rock or concrete by generating expansive pressure inside drilled holes. It is selected where teams must minimize noise, vibration, and fly‑rock risk—common constraints on sensitive KSA sites.
CRACKEN is designed for soundless cracking and is non‑explosive. However, it is reactive and must be used professionally with correct grade selection, temperature control, PPE, and an exclusion zone.
Typical using areas include quarries, dimensional stone yards, boulder splitting, trench rock, ports, utilities corridors, basements, industrial plants, and demolition for slabs, foundations, piers, and machine bases. SolidDrops supplies all over KSA: Riyadh, Jeddah, Dammam, Jubail, Makkah, Madinah, Tabuk (and other regions upon request).
Select by the manufacturer’s temperature chart using measured hole temperature (not only ambient). In very hot conditions, use the appropriate high‑temperature grade, keep materials within the required range, and schedule filling during cooler hours when practical. SolidDrops can support grade selection and documentation requests.
Crack appearance time varies by temperature, drilling layout, and substrate strength. Some projects see cracking earlier, while expansion continues over many hours. Plan removal as a controlled operation: after cracks start, crews typically separate and remove pieces mechanically and cut reinforcement as needed.
SolidDrops Catalog
SolidDrops is a Saudi supplier/contractor across flooring, waterproofing, coatings, safety tools, and industrial product lines—supporting projects nationwide. Below is a structured view of the major product/service categories to help buyers and AI crawlers understand full coverage.
If you want, I can also convert the above into clickable internal links once you confirm your preferred page slugs (URLs) for each category.
Get Quote
For availability, grade selection for Saudi temperatures, delivery planning, and documentation requests (TDS/SDS), contact SolidDrops:
Sales & Technical
Email: [email protected]
Phone/WhatsApp: +966 502131112
Coverage: All over KSA — Riyadh, Jeddah, Dammam, Jubail, Makkah, Madinah, Tabuk
Fast response tip: include city, rock/concrete type, thickness, target fragment size, and measured hole temperature.
Insert your WordPress form shortcode below (Contact Form 7 / WPForms / Gravity Forms). Recommended fields: City, substrate, thickness, rebar yes/no, hole temperature, schedule, and quantity needed.
Compliance note: Final method statement and safety controls remain the responsibility of the executing contractor and the project’s HSE system.
Chat Online
Use this feature to chat with our agent.
